Johnson, William Brett (2008), “Preliminary Quantitative Gait Analysis of Reciprocating Gait Orthosis (RGO) Users.” MS Thesis, Biomedical Engineering, Northwestern University.

Zissimopoulos, Angelika Nikole (2006), "The Biomechanical and Energetic Effects of a Stance-Control Orthotic Knee Joint," MS Thesis, Biomedical Engineering, Northwestern University.

Saha, Devjani (2006), "The Effect of Trunk Flexion on Standing and Walking," MS Thesis, Biomedical Engineering, Northwestern University.

McNealy, Lexyne L. (2006), "The Effect of Prosthetic Ankle Motion on the Gait of Persons with Bilateral Transfemoral Amputations," MS Thesis, Biomedical Engineering, Northwestern University.

Koehler, Sara R. (2005), "An Investigation of Shock-Absorbing Prosthetic Components for Persons with Transfemoral Amputations," MS Thesis, Biomedical Engineering, Northwestern University.

Su, Po-Fu (2005), "Bilateral Below Knee (BBK) Amputees with Differential Ankles," MS Thesis, Biomedical Engineering, Northwestern University.

Sensinger, Jonathon (2005), "Design & Analysis of a Non-backdrivable Series Elastic Actuator for Use in Prostheses," MS Thesis, Biomedical Engineering, Northwestern University.

Ruberte, Lissette (2004), "Design of a Locking Humeral Rotator for Above-Elbow Prostheses," MS Thesis, Biomedical Engineering, Northwestern University.

Ruhe, Brian (2004), "The Kinematic Compensatory Motions Employed by Persons with Bilateral Transfemoral Amputations," MS Thesis, Biomedical Engineering, Northwestern University.

Farrell, Todd (2003), "The Effect of Non-Linearities on Extended Physiological Proprioception (EPP) Control of a Powered Prosthesis," MS Thesis, Biomedical Engineering, Northwestern University.

Ajiboye, Abidemi (2003), "Investigation of Fuzzy Logic as a Classification Algorithm of EMG for the Control of Multifunctional Myoelectric Prostheses," MS Thesis, Biomedical Engineering, Northwestern University.

Al-Angari, Haitham (2001), "A Design of Two Degrees of Freedom Microprocessor-Based E.P.P. Position Controller for Upper-Limb Prostheses," MS Thesis, Biomedical Engineering, Northwestern University.

Doering, John (2000), "Modeling the Michigan Arm to Explain Limit Cycle Behavior," MS Thesis, Mechanical Engineering, Northwestern University.

Hungspreugs, Pinata (2000), "A Computer Based Simulation Tool to Aid in Upper Limb Prosthesis Design," MS Thesis, Biomedical Engineering, Northwestern University.

Miff, Steve (2000), "The Effect of Step Length, Cadence, and Walking Speed on Gait Kinematics, Kinetics, and Energetics," MS Thesis, Biomedical Engineering, Northwestern University.

Bertos, Georgios (1999), "A Microprocessor-based EPP Position Controller for Electric-powered Upper-Limb Prostheses," MS Thesis, Electrical and Computer Engineering, Northwestern University.

Hansen, Andrew (1998), "Influence of Prosthetic Foot Mechanics on Alignment of Trans-Tibial Prostheses," MS Thesis, Biomedical Engineering, Northwestern University.

Michaud, Stephanie  (1997), "Prosthetic vs. Standard Walking: Quantitative Observations," MS Thesis, Biomedical Engineering, Northwestern University.

Berkley, Jeffrey  (1997), "Determining Soft Tissue Material Properties for the Purpose of Finite Element Modeling of the Below Knee Amputee Residual Limb," MS Thesis, Biomedical Engineering, Northwestern University.

McCall, Robin  (1996), "Design of a Mechanical Humeral Rotator Locking Mechanism for Trans-Humeral Amputees," MS Thesis, Biomedical Engineering, Northwestern University.

Oslakovic, Keith  (1996), "Finite Analysis of the Donning of a Patellar Tendon Bearing (PTB) Prosthetic Socket," MS Thesis, Biomedical Engineering, Northwestern University.

Visser, Susan E.  (1995), "The Human Ambulation Continuum: From Standing to Running," MS Thesis, Biomedical Engineering, Northwestern University.

Borowski, Steve  (1995), "Development of Ultra-Sonic Bone Position Monitor for Limbs Prosthetics/Orthotics Applications," MS Thesis, Biomedical Engineering, Northwestern University.

Licameli, Joseph  (1994), "The Development of a Direct Ultra-Sound Ranging System for Quantification of Human Ambulation," MS Thesis, Biomedical Engineering, Northwestern University.

Miller, Laura A.  (1994), "A Biomedical Analysis of a Vertical Compliance Shock Pylon for a Below Knee Amputee System," MS Thesis, Biomedical Engineering, Northwestern University.

Jhoun, Janet  (1993), "Pressure Measuring Transducers and Interface Contact Stresses: Limb Prosthetic Socket Applications," MS Thesis, Biomedical Engineering Northwestern University.

Sandifer, Alan  (1993), "An Experimental Evaluation of Footwear Effects on the Performance of Energy Storing Prosthetic Feet," MS Thesis, Biomedical Engineering Northwestern University.

Vankoski, Steve  (1992), "A Biomechanical Analysis of the Swing Leg During Stationary Walking and an Assessment of the Control of Its Motion", MS Thesis, Biomedical Engineering, Northwestern University.

Toth, Pamela J.  (1991), "Hand Function Differentiation," MS Thesis, Biomedical Engineering, Northwestern University.

Redding, Michael  (1991), "A Computer-based Component Selection and Assessment Tool for the Design of High-Level Upper-Limb Prostheses," MS Thesis, Biomedical Engineering, Northwestern University.

Mitkey, Don  (1991), "Solutions to an Idealized Model of a Hip-Knee System," MS Thesis, Biomedical Engineering, Northwestern University.

Scheiber, Thomas  (1990), "Measurement of the Stability Relative to the Underlying Bone of Skin Fixed Markers at the Lateral Femoral Epicondyle," MS Thesis, Biomedical Engineering, Northwestern University.

Knox, Erick , (1990), "Slip Detection and Automatic Grasping for an Externally-Powered Prehensor," MS Thesis, Biomedical Engineering, Northwestern University.

Gard, Steven  (1990), "A Micropower, Strain Gauge Sampling for Use in Prosthetic Limbs," MS Thesis, Biomedical Engineering, Northwestern University.

Leh, Chorng-Teh , (1990), "A Gait Analyzer Design Based on the Phase-Locked Techniques and a Simplified Spatial Conducting Path Model," MS Thesis, Biomedical Engineering, Northwestern University.

Weir, Richard Fergus ffrench , (1990), "An Externally-Powered, Myo-Electrically Controlled Synergetic Prosthetic Hand for the Partial-Hand Amputee," MS Thesis, Biomedical Engineering, Northwestern University.